- Rain x wiper blades installation small j hook driver#
- Rain x wiper blades installation small j hook free#
If you are distracted or simply can't remember exactly how the new blades should fit into the wiper arm, don't worry. If the wiper arm gets away, it snaps back on your glass, even if it is only a few inches away.Īs soon as the hook is attached to the new windscreen wiper, it is swiveled back into the glass with one hand and placed on the refill wipers. To start removing the wiper blades, double the towel over the hook arm and pull it back into the glass and push the refill wipers back to where you took out the old wiper. I recommend keeping the windscreen wipers away from the windscreen with one hand throughout the process and a folded towel to protect the windscreen from falling back when you try to replace them. If they are not in balance, bend them slightly with the hook arm before adjusting them, but not too much. The trigger is located on the wiper blade, and if the wipers are not balanced, bend slightly to adjust the blades.
Rain x wiper blades installation small j hook free#
To remove the old wiper blades from the hook arm J, press the Tab button on the connection between the adapter and clip and pull the wiper blades free from an open end of the aJa. If you replace the wiper blades of your windshield wipers with a hook type wiper arm, you must first remove the old wiper blades by lifting and turning the blades and then lifting them off the wiper arm. Set the PIAA wiper down against your windshield and perform the same steps for the opposite side.Replacing your vehicle's wiper blades is not as difficult as you might think, but the process may be slightly different depending on the adapter the vehicle uses to attach the wiper blades to its wiper arm.Īs we will discuss later, the hook type wiper blade arm uses a locking flap that connects it to the wiper blades.You may even hear an audible 'click' confirming the two components have locked together. Slide the PIAA wiper forward to completely engage the "J-Hook". Take one of the PIAA wiper blades and place it underneath and just behind the "J-Hook", taking note of it's orientation to the adapter mount on the wiper.Confirm which wiper goes where and set them on the hood. Your PIAA Si-Tech Wiper Blade kit will also reflect this.
Rain x wiper blades installation small j hook driver#
As equipped from the factory, your vehicle may have two different lengthed wipers designated for the driver and passenger sides.Give it a wiggle if it's being a bit stubborn. You should now be able to pull the worn wiper blade back and disengage it from the J-Hook.For removal of the J-Hook attachment point on your worn wiper blades, use a small flat-bladed screwdriver to pry the front portion of the pivot section up.If your wiper arms do not lift off the windshield that high, take care while performing the replacement process that you do not allow the wiper arm to slip your grasp and snap back against the windshield. Pivot the wiper arm up until it stops in approx a 90 degree position from the windshield.For the "J-Hook" style of attachment, you will only be using the adapter already affixed to the PIAA Si-Tech Wiper Blades.You should have the PIAA wiper blade itself along with a selection of adapters. Remove the remainder of the components from your PIAA Si-Tech Wiper Blade packaging and lay out all the included parts.The window prep pack will clean the street grime and dirt while providing long lasting, water-beading technology that will make dirt, water, and grime flow off your vehicles windshield with ease. Wipe down the windshield with this pad as it is designed to work in conjunction with the PIAA Si-Tech Wiper Blades.
Open the wiper blade packaging and pull out the included PIAA Silicone Prep Pack.If necessary, clean the wiper arms and their attachment points as well. If your windshield is dirty, take a few moments to give it a good cleaning in preparation for your new wiper blades.Park your vehicle in a well-lighted and clean area.
0 kommentar(er)
